Remote view login failed on my PC Based DVR system. How to fix it?


If you have a DVR system that’s PC Based, and you already setup your system ready for remote viewing using our PDF MANUAL and when you try to connect, you get an error saying ” Log in Failed ” and if you check on the Log you see that you actually log in and then the system log you out.

The Problem is the ROUTER. The router limits the Bandwidth. So the solution is to Enable the DMZ service on the Router to the IP address of the DVR System.

On some Routers may say DMZ SERVICE or DMZ SERVER or just DMZ.

This error is most common on the following DVR Capture Cards.

DV-9120
DV-9480
DV-9240
DV-9424
DV-9030
DV-9060
DV-9448
DV-9808
DV-9816
DV-9824
DV-9832

1.3M Pixel IP Camera, 700 TVL, Dual Codec, Two way audio, Low bandwidth usage, Day and Night

GeoVision, the name brand in CCTV security, introduce the DM-IP-13GV IP CCTV Camera with 1.3 Mega pixels, providing detail not seen on conventional surveillance cameras

the DM-IP-13GV allows users to monitor critical areas with greater detail than ever. Moreover, with simultaneous/dual video stream and support for compliant Power-over-Ethernet (PoE), it allows users to view both MJPEG images and MPEG-4 videos with improved efficiency while conserving valuable bandwidth.

Progressive scan CCD captures the entire scene of a moving object at the same time. Even and odd fields are scanned simultaneously.

Crimp-on Male BNC Connector, Compression Waterproof

The DM-CN-016 is a male BNC crimp-on connector, designed to be compressed on the cable, thus providing much tighter, waterproof crimp. It is intended for use on RG59 coax cables. Crimping can be done using our Compression Crimp tool DM-CBT-RG5960.
This professional Crimping tool provides good and consistent crimp every time. It’s insulated, cushioned, comfort grip handles, provide comfort and maximum crimping force. It is light enough to fit conveniently in an installer’s belt. For Crimping RG59, RG6 and Waterproof Compression Connectors.

Heater Blower Outdoor w/ Housing, 1/4″ SONY Super HAD Exview CCD 470 TVL, 0LUX 84 Infrared LED’s up to 180ft

The DM-IR 25HOHB is a one of a kind solution designed to solve the problem of mounting an IR camera inside a housing. The DM-IR 25HOHB has a heater and blower to out stand severe weather, the IR LED’s are mounted at the front of the housing for clear illumination of up to 180 feet, and the camera offer crystal clear resolution of 470 TV lines, a 6.0-15.0 mm Vari-Focal Auto Iris Lens. This camera work on 24V AC.

Great for Winter and Summer weather conditions

Geovision MPEG-4 / H.264 PC Capture Card, 480 FPS Display, 120FPS Recording, 8CH Video, 8CH audio, TV Output, Windows XP / Vista compatible

When it comes to security DVR capture cards, Geovision is the name everybody is looking for. The DM-CC-GV1120/8 is a Pro-Grade Security DVR board offering quality for low budget. It supports up to 8 video channels with a crystal clear high-res picture quality, 480 FPS playback and a maximum 120 frames per second recording plus 8 channels of audio. The high compression MPEG4 and H.264 CODEC provides more recording time with same size hard disk drive. The built-in video motion detector logic helps the DVR system from storing unnecessary video.

  • 8 channel video input
  • 8 channel audio input
  • 480 fps display frame rate
  • 120 fps record frame rate
  • Full D1, Half D1, CIF Resolution
  • Compression: MPEG4, H.264
  • TV Output (RCA x1)
  • Microsoft Windows XP /Vista Compatible

*Note: DM-CC-GV1120/8 is currently not compatible with VIA series and ATI series chipset motherboards !

There is also a 4 Channel Geovision Card using the Same technology

Triplex 16Ch Security DVR System, H.264 Hardware Compression, 480 FPS Display, 240FPS Recording, 16CH Video, 1CH Audio

The DM-DV-APO264/16 features the industry’s first full-scale Real-Time 16Ch H.264 hardware compression standalone DVR. According to extensive laboratory and field testing, recorded data based on H.264 is 4.5 times smaller than typical MPEG-4, or 3 times smaller than conventional MPEG-4 codec. The hardware codec of DM-DV-APO264/16 truly is superior in all aspects of performance, delivering your experience through remote PC access or DSP-based H.264 services or smart phone are phenomenal.

It also Comes In 4 Channels & 8 Channels
Specifications

  • 16 Channel Video Inputs / 1 Channel Audio Input
  • H.264 hardware-based codec for superior video compression
  • Real-Time 16 Channel display at 480 FPS / IPS Total
  • Customizable Channel Rotation Delay
  • Supports Hi-resolution VGA monitors and 16 channel loop back composite monitors
  • Intelligent Video Motion Detection (VMD)
  • Audio, Alarm I/O & RS-232, RS-485 PTZ Camera Interface
  • Local backup via USB-based storage media or CD/DVD writer
  • SATA interface for high-speed reliable recording on HDD
  • Wide system integration (SI) capabilities
  • User-friendly OSD operation with 15 languages support
  • Web-based H.264 surveillance client software or Web Services
  • Feature-rich remote management & surveillance software

Integrated Remote System

  • Web-based surveillance anywhere
  • Microsoft Windows XP (and Higher )
  • Remote management
  • Remote monitoring
  • Remote playback
  • Remote search
  • Remote backup

Close Range License plate Capture camera, 8mm fixed lens, up to 5 MPH and 16.5 ft, 12 IR LED’s, bracket included

The DM-IR 85LPH is a close-range license plate capture security IR camera that provides high quality plate images in day or dark conditions. Powerfully effective and user friendly, the DM-IR 85LPH is ideal for meeting the surveillance needs of gated communities, gas stations, bars, drive-through locations, casinos and toll gates.

This IR security camera is working on 12V DC and the bracket (which features a hidden cable mount) is included.

It’s powerful features include the ability to capture the license plate of a car moving up to 5 MPH, and it’s 8.0 mm fixed lens allow the capture of plates with a distance of 16.5 ft.

Basics ways to check what’s your LAN settings for Remote Viewing Setup.


Basics ways to check what’s your LAN settings for Remote Viewing Setup.

For Windows XP / Vista.

Click on the START Menu.
Find a link called RUN and click on it.
On the RUN window type CMD and press enter
On the CMD window type IPCONFIG and press enter
It will show you your LAN settings. For Example:

Ethernet adapter Local Area Connection:

IP Address. . . . . . . . . . . . : 192.168.1.116

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . . : 192.168.1.1

Always Keep in mind that the Default Gateway it’s your Router’s IP Address.

On the Stand Alone DVR System you will need to change the Network Setting to the ones that your network has.

For Example

IP Address. . . . . . . . . . . . : 192.168.1.200

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . . : 192.168.1.1


Once Ip address it’s change on the DVR you can Ping it by using the PING command on the CMD Window. Example
PING 192.168.1.200

You will get a reply from DVR.

Now you can Setup the DVR Remote Viewer Software and type the local ip address of the DVR and you are ready to see your Cameras from the Same Location

General Settings For Remote Viewing Connection

DVRMASTER.COM
General Settings For Remote Connection

1. Connect the DVR system (PC Base Or Stand Alone) To a network that has internet Active (via Cat5 Cable, Ethernet Cable.)
For Stand Alone System you will Do the following Steps.

Once the DVR Connected to the Network With internet Active Please Log into the DVR by pressing the MENU or Setup Button On the DVR Itself.

2.1: Please refer to the DVR manual so you can navigate to the Network Settings and find out what is the IP Address Of the DVR.
2.2: Now Go to A Computer that is Connected on the same Network as the DVR, and Click ( Start > Run >(type) CMD> And Press Run (In case your DVR Is PC Based you will do this on the same System)
2.2 Example

cmd.jpg

2.3
: On the Command Window you will type IPCONFIG so you can see what’s the IP address of your Computer and the IP address of your Router or Modem Router. You will also See what’s the Subnet Mask. You will need all of these settings in order to setup the DVR System (In case your DVR Is PC Based you only have to assign an STATIC LOCAL IP ADDRESS ) Refer to Steps 3 For More Information ipconfigall.jpg
2.4: Now go back to the Network Settings on the DVR were you can see the IP address of the system. Make sure you have the Same SUBNET MASK and the same DEFAULT GATEWAY settings that you copy from the Computer.
subnet.jpg
2.5: Please Assign an IP Address to the DVR that’s not on your Network. To see if the Ip Address you are going to assign to the DVR it’s not Taken Please Go back to the Command window and you will type PING (IP ADDRESS) and press Enter
(In case your DVR Its PC Base You don’t need to assign an IP Address because it already has one)

Example ( Ping 192.168.1.100 ) If the Ip address is Taken you will get a reply.

Pinging 192.168.1.100 with 32 bytes of data:

Reply from 192.168.1.100: bytes=32 time<1ms TTL=64

Reply from 192.168.1.100: bytes=32 time<1ms TTL=64

Reply from 192.168.1.100: bytes=32 time<1ms TTL=64

Reply from 192.168.1.100: bytes=32 time<1ms TTL=64

Ping statistics for 192.168.1.111:

��� Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

��� Minimum = 0ms, Maximum = 0ms, Average = 0ms

If the Ip address is not taken you will Get a Request Time Out.

Pinging 192.168.1.145 with 32 bytes of data:

Request timed out.

Request timed out.

Request timed out.

Request timed out.

Ping statistics for 192.168.1.145:

��� Packets: Sent = 4, Received = 0, Lost = 4 (100% loss)

Make Sure you are assigning an Ip address that it’s not taken by any other device on the Network.
For Example
IP Address. . . . . . . . . . . . . : 192.168.1.145

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . : 192.168.1.1

2. 6: Now that you had Assigned an IP Address to the DVR now you can use the PING Command to see if you get a Reply from the DVR. If you Do get a reply you had Successfully Assigned an IP to the DVR.

2.7: Now Log into the Router by Typing the IP address on the Address Bar on a Internet Window. If you don’t know what’s the Ip Address of your Router please refer to the DEFAULT GATEWAY settings when you typed IPCONFIG on the Command Window. (In case your DVR Its PC Base you will do this on the same DVR System)

ROUTERIP.jpg

2.8: You will need to see your Router’s Manual To Find where you can find the Settings for (PORT FORWARDING) In there you will need to Forward the Ports that the DVR requires in order to Remote Connect to it. ( See DVR Manual to check what Ports are needed to be forward to the DVR. This Apply to PC BASE DVR & STAND ALONE SYSTEMS.
Once you had found the Port Forwarding page on the router, Forward the Correct ports to the IP Address of the DVR. Please Make sure you Forward the Ports on ‘TCP & UDP’ Protocols. This Image shows you an Example of how it’s made.

ports.jpg



If you are not Sure where to go to the PORT FORWARD Page on your Router Please See this following Page that will Show you almost all the Routers On the Market.

http://portforward.com/routers.htm


2.9: Once Ports are forwarded you will need a Computer that is connected to the internet on the same network and go to http://canyouseeme.org In the Box where it say What Port You need to type the PORT that you forwarded to the DVR system. (In case your DVR Its PC Base you Need to have the DVR SOFTWARE OPEN in order to test if the ports are correctly Forwarded)

For Example

port.jpg

You Need to see SUCCESS in order for you to go to the Next step.

If you get ‘Error: I could not see your service..‘ you need to contact your Router or Modem Manufacture so they can help you do the Port Forwarding correctly, or just double check what you did wrong.

2. 10:If you see SUCCESS you can now See your DVR locally and From a Different Location by typing your IP address of the DVR Location.

2. 11: To see your DVR Locally you can now Type the IP Address of the DVR on the Web Browser (Only if the DVR has the WEB SERVER SUPPORT) If the DVR Does not support Web Server then you can use the SOFTWARE that came in a CD with the DVR you Purchased. (This Apply to PC BASE DVR & STAND ALONE SYSTEMS)


2. 12: Please refer to the DVR manual to use the DVR REMOTE SOFTWARE.

2.13: You have successfully setup your DVR for Remote Viewing Locally and From a Different Location.

FOR PC BASE DVR Follow These Steps in this Specific Order.

2.2
2.3
3:
To set up an Static IP Address on PC Based please see the following Steps.
Got to STAR>Control Panel>Network Connections>Local Area Connection (Right Click and Click Properties)> Internet Protocol (TCP/IP)Select and Click Properties> Then type the Static Ip you would like to assign. See picture below for more information. (Example.)

Staticip.jpg
3.1: Once you have assign an Static IP Address to the PC Based DVR system follow the next steps. You will need to see the steps above in this specific order.

2.7

2.8

2.9

2.10

2.11

2.12

Finish!

Professional 8.7″ Hex Series Crimping Tool for security camera Connector

This 8.7″ Hex series professional Crimping tool provides good and consistent crimp every time. It’s insulated, cushioned, comfort grip handles, provide comfort and maximum crimping force. It is light enough to fit conveniently in an installer’s belt. For Crimping F, N, BNC, TNC, UHF, ST, SC, SMA Etc. Connectors, Cord end terminals, insulated and non-insulated terminals.

  • 8.7″ overall length
  • Professional Ratchet type
  • For Crimping Connectors: F, N, BNC, TNC, UHF, ST, SC, SMA
  • For insulated & non-Insulated terminals
  • Cushioned, comfort grip handles
  • Lightweight